Tyco-electronics 0-1591093-X User Manual

24 and 16 Port 10/100Mbit/s Ethernet Smart Switch II with Optional Fibre Uplink Port - Product User Guide Introduction

24 and 16 Port Smart Switch II – User Manual Page 10 Programming The Switch The switch can be managed using a PC via the front panel RS232 consol

24 and 16 Port Smart Switch II – User Manual Page 11 Press <CR> return key several times to view the main start-up screen :- Figure 6 -

24 and 16 Port Smart Switch II – User Manual Page 12 Port State This menu lists the entire port status of the switch. From the main menu type num

24 and 16 Port Smart Switch II – User Manual Page 13 Port Configuration This Menu allows for the configuration of all the ports on the switch. Fr

24 and 16 Port Smart Switch II – User Manual Page 14 The configurable items are shown in the table below :- Port Selects the port to be config

24 and 16 Port Smart Switch II – User Manual Page 15 Trunk Status This Menu shows if faults are present on trunks that have been configured. If

24 and 16 Port Smart Switch II – User Manual Page 16 QOS This menu can be used to configure the priority of traffic through the switch. Three ty

24 and 16 Port Smart Switch II – User Manual Page 17 It is important that only one method of QOS is enabled on the switch at any one time. Enabl

24 and 16 Port Smart Switch II – User Manual Page 18 Port Tagging Control This menu can be used to control the priority tag on Ethernet packets l

24 and 16 Port Smart Switch II – User Manual Page 19 operation of the entire switch. By selecting item 7 from the main menu the following screen

24 and 16 Port Smart Switch II – User Manual Page 2 Package Contents Unpack the contents and verify them against the

24 and 16 Port Smart Switch II – User Manual Page 20 Switch Name – This item can be used to name the switch. This name is then shown at the top o

24 and 16 Port Smart Switch II – User Manual Page 21 Select Y and the factory defaults will be loaded. VLAN Member Setup The 16 and 24 Smart Swit

24 and 16 Port Smart Switch II – User Manual Page 22 Adding VLANS To Insert a VLAN I should be inputted and this will add a new VLAN. Keep typing

24 and 16 Port Smart Switch II – User Manual Page 23 Save configurations Any configuration changes made to the switch will need saving to non-vol

24 and 16 Port Smart Switch II – User Manual Page 24 LED Indicators The diagnostic LED indicators located on the

24 and 16 Port Smart Switch II – User Manual Page 25 Trouble Shooting Power 1. Verify that the AC power is present a

24 and 16 Port Smart Switch II – User Manual Page 26 Product Specification Standards Compliance IEEE802.3 10BASE-T IEEE802.

24 and 16 Port Smart Switch II – User Manual Page 27 Optical Port Specifications Optical Transceiver TX power RX sensitivity Power Budget 100Mbp

24 and 16 Port Smart Switch II – User Manual Page 28 Table Of Contents INTRODUCTION...

24 and 16 Port Smart Switch II – User Manual Page 29 24 and 16 Port Smart Switch II – User Manual Page 29 Product Number 0-1591093-x 0-159

24 and 16 Port Smart Switch II – User Manual Page 3 Features: - ! 24 or 16 x Auto-sensing 10/100Base-T RJ-45 Ethe

24 and 16 Port Smart Switch II – User Manual Page 4 Front Panel The front panel of the switch has 24 or 16 x R

24 and 16 Port Smart Switch II – User Manual Page 5 Installation Copper and Fibre Cabling Guidelines

24 and 16 Port Smart Switch II – User Manual Page 6 Desktop Installation 1. Locate the switch in a clean, flat and safe position that has easy a

24 and 16 Port Smart Switch II – User Manual Page 7 Completing the Installation When the switch has been installed as specified above, then the u

24 and 16 Port Smart Switch II – User Manual Page 8 Optional Fibre Uplink Port This switch can support one single or dual plug-in optical port t

24 and 16 Port Smart Switch II – User Manual Page 9 These option modules are installed as described on page 6. The following plug-in fibre modul